What Rims for your VR4 - the "do they look pretty" thread
- Thread starter hawks
- Start date
naughtika
OzVR4 Stalker
hehe funny.. it took me about 10 minutes to create the poll
bradc
1 AYC Bar
P1's!
SLY-031
Leaving Skid Marks
9" wide or bust! haha.
9" +30 to +38 will fit, just require minor guard love, but it is worth it
9" +30 to +38 will fit, just require minor guard love, but it is worth it
bradc
1 AYC Bar
9" 30mm will require serious guard love
SLY-031
Leaving Skid Marks
But fark will it look hot if the car is low enough
put a 235 on, pull about 20mm out of your guards and you're laughing.
put a 235 on, pull about 20mm out of your guards and you're laughing.
CR Kai's for me....
J-B
Leaving Skid Marks
hey guys, can someone tell me if rims with these specs will fit on a prefacelift
18x8.5 offset +30
cheers
18x8.5 offset +30
cheers
leebutts
1 AYC Bar
Nope, +38 is the smallest offset you want to go without wheel arch extensions/flares.
SLY-031
Leaving Skid Marks
Not true.
8.5 +30 will sit 2mm further out than my 9 +38's.
So yes, they will fit. Minor guard roll on the rear with a 235/40R18. Fronts will hang only a little. This is assuming the car is lowered a little to take advantage of the natural cambering in of the suspension...
8.5 +30 will sit 2mm further out than my 9 +38's.
So yes, they will fit. Minor guard roll on the rear with a 235/40R18. Fronts will hang only a little. This is assuming the car is lowered a little to take advantage of the natural cambering in of the suspension...
G
Guest
Unregistered
My babies have arrived, now the painful wait to $ave for tyres...
17x8 +35
Tyres are 245/45/17 at the moment (came with the rims) so they aren't going on the car till I can sort out swapping of the 215/45/17's over to the new wheels, and some springs as fitment is rather mexican at stock height.. but it's getting there!
Tyres are 245/45/17 at the moment (came with the rims) so they aren't going on the car till I can sort out swapping of the 215/45/17's over to the new wheels, and some springs as fitment is rather mexican at stock height.. but it's getting there!
bradc
1 AYC Bar
perfect at the back, need to be 10mm further in at the front though How is clearance on the rear suspension arm, it must be close?
How is clearance on the rear suspension arm, it must be close?
SLY-031
Leaving Skid Marks
With some skinnier tyres you'll have no issues with clearance at all
Gotta love good fitment Must say though, 17's look tiny on a Legnum...
Gotta love good fitment
Must say though, 17's look tiny on a Legnum...
SLY-031
Leaving Skid Marks
perfect at the back, need to be 10mm further in at the front though
16mm more than mine, i.e. SHITLOADS!
Lowering will take care of the mexican-ism.
Well for the bargain price they were I couldnt resist sticking with 17's - I just wanted something that had decent width/offset
Now at least with the $$ I saved, I can lower it, giving me propper fitment and stance... just the diameter isn't quite where I want it but oh well.
Now at least with the $$ I saved, I can lower it, giving me propper fitment and stance... just the diameter isn't quite where I want it but oh well.
G
Guest
Unregistered
what car did they come off lee?
They came off an R33 GTS-t - of which they were an OK fit on that at the front, but too skinny at the rear.
Similar threads
